How To Install Bolt Lock

How to Install a Deadbolt Lock

Updated: Sep. 02, 2022

Keep unwanted guests from coming through your doors

Family unit Handyman

To meliorate the security of your home, you could get a dog with a bark vicious enough to scare the rust off a statue. But one of the easiest, least expensive and nigh constructive security measure you can accept is to install a heavy-duty deadbolt. Here'south how.

You might also like: TBD

Complication

Beginner

What you demand to know to larn how to install a deadbolt lock

Marker the door

Mark the door for drilling by taping the template to the inside of the door (wood doors have a bevel that will throw the measurements off if you utilize the outside side). Place the template so the center of the deadbolt will be 6 in. above the center of the doorknob.

Drill the cylinder hole

Drill out the cylinder hole with the ii-one/viii in. hole saw. Utilize the same setback (distance from door border to hole middle) as the doorknob, either two-3/8 in. or ii-3/4 in. Later on the pigsty saw's pilot bit pokes through the opposite side, remove the scrap wood protector and cease drilling the cylinder pigsty from the exterior side.

Drill the bolt hole

Adjacent, drill out the bolt hole in the center of the door edge with the 1-in. hole saw or spade bit. Keep your drill level and square as you make these holes.

Chisel a recess for the faceplate

Chisel out the recess for the rectangular faceplate by inserting the bolt latch set into the door and marking the profile of the faceplate onto the door edge. Use a abrupt 1-in. chisel to remove plenty material to allow the faceplate to be flush with the door edge (usually about 3/16 in.).

Tip: Cut the vertical edges with a utility knife to avoid accidentally splitting the door with the chisel.

Mark the jamb

Mark the jamb for the strike plate and box by blanket the commodities end with lipstick (install the cylinder and commodities first). Next, mark the contour of the strike plate on the jamb. Then, drill out for the strike box by drilling overlapping 1-in. holes. Finally, chisel out the recess for the strike box and plate.

Secure the strike box

Secure the strike box to the jamb and the 2×4 frame backside it. Drill pilot holes for the screws. Mostly, the jamb volition have a hollow space backside it. So go slowly to avoid warping the jamb by driving the screws likewise deep.

Single-cylinder deadbolts (keyed on one side) will work fine for most situations. Double-cylinder deadbolts (keyed on two sides) are a good idea if you take a window nigh the deadbolt. For safety reasons, if you choose a double-cylinder deadbolt, make absolutely certain your family unit knows where the key is and leaves information technology in that location.

Calling a locksmith out for this how to install a deadbolt lock chore volition toll $150 or more, simply y'all can install a heavy-duty deadbolt yourself in less than an 60 minutes for a third of the price. That's virtually boilerplate for a good deadbolt and a hole saw fix. To cutting through a steel door, brand sure you get a "bimetal" hole saw set.

Next, check out x amazing modern front doors.

Apply a Class i deadbolt. Deadbolts take a grade rating of 3 to 1 (1 is the toughest). Nearly abode centers carry Form ane deadbolts, such as Schlage's Maximum Security Deadbolt, just you lot may have to chase for them. Expect to pay $27 to $35 for a Grade 1.

Install a strike box. A strike box strengthens the deadbolt past spreading the impact of a forced entry over a wider surface area and by helping tie the strike to the two×4 frame, not merely the jamb. You can become a separate strike box for about $seven at domicile centers.

Use the rectangular faceplate. Most deadbolts permit you to choose betwixt a rectangular faceplate and a round one that doesn't require chiseling. Unless you have a steel door, don't be tempted! The rectangular faceplate, recessed into the door, makes a stronger setup.

Check out 22 more ways to inexpensively theft-proof your home.

Required Tools for this How to Install a Deadbolt Lock Project

Have the necessary tools for this DIY projection lined up earlier you lot start—y'all'll save time and frustration.

Required Materials for this How to Install a Deadbolt Lock Project

Avoid concluding-minute shopping trips by having all your materials ready ahead of time. Here's a listing.

Originally Published: January 24, 2022

Similar Projects

Source: https://www.familyhandyman.com/project/how-to-install-a-deadbolt/

Posted by: strainhusafter1999.blogspot.com

Share this post